Today you build 5 min
Hi! I am AdvasBot.
Today we build the Wipers!
The arm goes this way. Then it goes that way.
A motor makes the arm move. You will make it move!
Where do we see it? 5 min

Cars have wipers. Buses have them too.
Rain falls on the glass. The driver cannot see.
The wiper pushes the rain away. Swish!
Building tips in the build
- Look at one picture at a time.
- Find the parts in the picture.
- Push the parts together. Click!
- Look again. Does it match the picture?
- Stuck? That is OK. Ask your teacher.
Wiper break! 5 min
Stand up. Be a wiper!
- Put your arms up high.
- Swing them this way. Swish!
- Swing them that way. Swish!
- Now go slow. Now go fast!
- Stop. Sit down. Well done!
Meet the parts 5 min
- The BrickIt is the robot’s brain. It has a screen.
- The motorIt turns. It makes the arm move.
- The cableIt joins the motor to the Brick.
Plug it in 5 min
The Brick has holes for cables. They are called ports.
This means the places a cable goes.
- Find the port with the letter A.
- Plug the motor cable into A. Click!
- Pull it a tiny bit. Does it stay in?
Talk to the Brick 5 min
The computer talks to the Brick. Your teacher will help.
- Press the middle button on the Brick. It turns on.
- Wait for the screen. It takes a little while.
- Your teacher joins the Brick to the computer.
- Look at the computer. Can you see a motor on A?
For grown-ups: how to connectUSB or Bluetooth, and what to do when it will not connect.Show meHide
Two routes, and either is fine. USB is the reliable one and the one to fall back on when a room’s Bluetooth is busy; Bluetooth leaves the robot free to move, which some models need.
How to connect the BrickUSB and Bluetooth, step by step, with a photograph of every screen. Open it if you have not done this before — or if pairing is not working.Show meHide
USB — the reliable one
- Switch the Brick on with the dark grey centre button.
- Cable into the Brick’s PC port — the small square socket beside the numbered ports, not one of the numbered ones.
- Other end into the computer.
Bluetooth — name it first
Do these in order. Naming the Brick after you go looking for it in the list is how groups end up driving each other’s robots.
- Name your Brick. On the Brick: Settings (the spanner) → Brick Name. Type something nobody else will pick, then press the tick. Every Brick is called
EV3until somebody changes it. - Turn Bluetooth on. Settings → Bluetooth. Tick Bluetooth and Visibility. Leave iPhone/iPad/iPod unticked.
- Connect from EV3 Classroom. Click the Brick icon at the top of the programming area, find your Brick by name, and click Connect.
- Say yes on the Brick. It asks “Connect?” with the computer’s name — choose the tick, then accept the passkey, which is already 1234.
EV3.The two failures, every class, every time. The Brick has gone to sleep while you were building — press the centre button to wake it. Or you have paired with the group at the next table, which is why the name matters.
The long version, including Port View and how to read the port tiles, is in the Brick & Bluetooth guide.
Make it move! 15 min
You need two blocks. Just two!
when program starts :: events hat [A v] run [clockwise v] for (1) [rotations v] :: motors
- Find the yellow start block. It says “when program starts”. It is already there.
- Find the motor block. It says “run”.
- Drag it under the start block. Click!
- Check the letter. It must say A.
- Press play. Watch the arm!
The block says 1. The motor turned one time.
One turn is called one rotation.
Your challenges 5 min
⭐ Challenge 1: Again!
Press play again. Does it do the same thing?
⭐⭐ Challenge 2: Watch the motor
Press play. Do not watch the arm. Watch the motor. What turns?
⭐⭐⭐ Challenge 3: Teach a friend
Show a friend your program. Tell them what each block does.
Tidy up 5 min
- Turn the Brick off. Your teacher will show you.
- Keep your Wipers in one piece. You need them next time!
- Put spare parts back in the box.
Well done! You built a robot!
Teacher note
Timing (90 min): photo and talk 5, real world 5, build 35, break 5, parts 5, ports 5, connect 5, first program 15, challenges 5, tidy 5. The build is the lesson today; if it runs long, cut the challenges, not the first program. Every child should press play once before they go home.
Connect each Brick yourself before the program section, and check the port view shows a Medium Motor on A. At six, pairing is a teacher job.
The arm is geared down, so one rotation of the motor moves the arm less than one turn. Check one rotation on a built model before class. If the arm reaches its end stop, tell the class to use a smaller number (for example 0.5) and show them where to type it.
Words met today: start block, motor, cable, port, rotation. Do not teach “clockwise” yet; that is lesson 2.
