Today you build 5 min
Hi! It is AdvasBot again.
Today we launch spinning tops!
This is the Dual Gyro. It has two spinning tops.
The motor turns a big gear. The gear spins the tops.
Then the tops fly off. Whee!
Where do we see it? 5 min

Have you played with a spinning top?
You twist it. It spins and spins.
A fast top spins for a long time.
Building tips in the build
- Look at one picture at a time.
- Count the teeth on the big gear. Lots!
- Push the parts together. Click!
- Turn the gear by hand. Does it turn?
- Stuck? That is OK. Ask your teacher.
Spinning top break! 5 min
Stand up. Find a space. Be a top!
- Put your arms out wide.
- Turn round slowly. One time.
- Now turn the other way.
- Wobble, wobble. The top slows down.
- Fall down softly. Sit up. Well done!
Meet the parts 5 min
This robot has a new motor. It is longer!
- The BrickIt is the robot’s brain.
- The big motorIt is long. It turns the big gear.
- The gearA wheel with teeth. It turns the tops.
This motor is called the Large Motor. Large means big.
Plug it in 5 min
Do you remember the ports? Motors go in letters.
- Find port A on the Brick.
- Plug in the motor cable. Click!
- Pull it a tiny bit. Does it stay?
Talk to the Brick 5 min
- Press the middle button. The Brick turns on.
- Wait for the screen.
- Your teacher joins the Brick to the computer.
- Can you see a motor on A?
For grown-ups: how to connectUSB or Bluetooth, and what to do when it will not connect.Show meHide
Two routes, and either is fine. USB is the reliable one and the one to fall back on when a room’s Bluetooth is busy; Bluetooth leaves the robot free to move, which some models need.
How to connect the BrickUSB and Bluetooth, step by step, with a photograph of every screen. Open it if you have not done this before — or if pairing is not working.Show meHide
USB — the reliable one
- Switch the Brick on with the dark grey centre button.
- Cable into the Brick’s PC port — the small square socket beside the numbered ports, not one of the numbered ones.
- Other end into the computer.
Bluetooth — name it first
Do these in order. Naming the Brick after you go looking for it in the list is how groups end up driving each other’s robots.
- Name your Brick. On the Brick: Settings (the spanner) → Brick Name. Type something nobody else will pick, then press the tick. Every Brick is called
EV3until somebody changes it. - Turn Bluetooth on. Settings → Bluetooth. Tick Bluetooth and Visibility. Leave iPhone/iPad/iPod unticked.
- Connect from EV3 Classroom. Click the Brick icon at the top of the programming area, find your Brick by name, and click Connect.
- Say yes on the Brick. It asks “Connect?” with the computer’s name — choose the tick, then accept the passkey, which is already 1234.
EV3.The two failures, every class, every time. The Brick has gone to sleep while you were building — press the centre button to wake it. Or you have paired with the group at the next table, which is why the name matters.
The long version, including Port View and how to read the port tiles, is in the Brick & Bluetooth guide.
Launch the tops! 15 min
This time you need three blocks.
when program starts :: events hat [A v] set speed to (75) % :: motors [A v] run [clockwise v] for (4) [rotations v] :: motors
- Find the yellow start block. It is already there.
- Add the speed block. Type 75. This makes the motor fast.
- Add the motor block. Type 4.
- Check the letters. Both must say A.
- Put the two tops on the robot.
- Stand back a little. Press play!
The motor turned 4 times. Four rotations.
Your challenges 5 min
⭐ Challenge 1: Again!
Put the tops back. Launch them again.
⭐⭐ Challenge 2: Which top wins?
Watch both tops. Which one spins longer?
⭐⭐⭐ Challenge 3: Count the turns
Watch the motor. Count out loud. Did it turn four times?
Tidy up 5 min
- Turn the Brick off.
- Find both tops. Put them with your robot.
- Keep your Dual Gyro in one piece. You need it next time!
- Put spare parts back in the box.
Well done! You launched two tops!
Teacher note
Timing (90 min): photo and talk 5, real world 5, build 35, break 5, parts 5, ports 5, connect 5, launch 15, challenges 5, tidy 5.
The motor is a Large Motor on port A (checked on the Level 1 page against step 9 of the manual). The program is the Level 1 one without the screen blocks: speed 75 %, then 4 rotations clockwise. Try it on a built model before class. If the tops do not leave at 75 %, raise the speed; if they fly too far, lower it.
The speed block is given, not taught. Say only “this makes it fast”. Speed is the idea of lessons 9 and 10.
Safety: tops leave the launcher fast. Clear a space, keep faces back, and launch onto the floor or a big table.
Words met today: Large Motor, gear, spin.
