Today you build 5 min
Hi! It is AdvasBot.
Today we build a shooter. Whoosh!
This is the Gear Shooter.
A wheel spins very fast. Then it throws a gear!
It is fun. But we must be safe.
Where do we see it? 5 min

These are gears. They are wheels with teeth.
One gear pushes the next one.
Bikes have gears. Clocks have gears. Toys do too.
Safe shooting rules 5 min
Learn these rules first. They are very important!
- Point it down the table. Never at a person.
- Never at a face. Not even your own.
- Fingers away from the spinning wheel.
- Look before you press play. Is the way clear?
Building tips in the build
- Look at one picture at a time.
- Count the teeth. Big gear or small gear?
- Push each gear in all the way.
- Turn the gears by hand. Do they turn freely?
- Stuck? That is OK. Ask your teacher.
Spinning break! 5 min
Stand up. Be a spinning wheel!
- Turn round slowly. Once.
- Roll your arms. Slow, then faster.
- Faster! Faster!
- Stop! Freeze like a statue.
- Sit down. Well done!
Meet the parts 5 min
- The big motorIt turns the gears.
- The gearsWheels with teeth. They push each other.
- The shooting wheelIt spins very fast. It throws the gear.
Plug it in 5 min
- Find port A.
- Plug the motor cable in. Click!
- Pull it a tiny bit. Does it stay?
Talk to the Brick 5 min
- Turn the Brick on.
- Your teacher joins it to the computer.
- Is there a motor on A?
For grown-ups: how to connectUSB or Bluetooth, and what to do when it will not connect.Show meHide
Two routes, and either is fine. USB is the reliable one and the one to fall back on when a room’s Bluetooth is busy; Bluetooth leaves the robot free to move, which some models need.
How to connect the BrickUSB and Bluetooth, step by step, with a photograph of every screen. Open it if you have not done this before — or if pairing is not working.Show meHide
USB — the reliable one
- Switch the Brick on with the dark grey centre button.
- Cable into the Brick’s PC port — the small square socket beside the numbered ports, not one of the numbered ones.
- Other end into the computer.
Bluetooth — name it first
Do these in order. Naming the Brick after you go looking for it in the list is how groups end up driving each other’s robots.
- Name your Brick. On the Brick: Settings (the spanner) → Brick Name. Type something nobody else will pick, then press the tick. Every Brick is called
EV3until somebody changes it. - Turn Bluetooth on. Settings → Bluetooth. Tick Bluetooth and Visibility. Leave iPhone/iPad/iPod unticked.
- Connect from EV3 Classroom. Click the Brick icon at the top of the programming area, find your Brick by name, and click Connect.
- Say yes on the Brick. It asks “Connect?” with the computer’s name — choose the tick, then accept the passkey, which is already 1234.
EV3.The two failures, every class, every time. The Brick has gone to sleep while you were building — press the centre button to wake it. Or you have paired with the group at the next table, which is why the name matters.
The long version, including Port View and how to read the port tiles, is in the Brick & Bluetooth guide.
Make it shoot! 10 min
A shooter needs a lot of speed. Use 100!
when program starts :: events hat [A v] set speed to (100) % :: motors [A v] run [clockwise v] for (2) [seconds v] :: motors
- Put set speed under the start block. Type 100.
- Put the motor block under it. Pick seconds. Type 2.
- Point the shooter down the table.
- Your teacher puts a gear in.
- Look. Is the way clear? Press play!
Your challenges 10 min
⭐ Challenge 1: Slow shot
Change the speed to 50. Does the gear go as far?
⭐⭐ Challenge 2: Mark the spot
Put a sticky note where your gear lands. Can you beat it?
⭐⭐⭐ Challenge 3: Hit the box
Your teacher puts a box on the table. Can your gear land in it?
Tidy up 5 min
- Turn the Brick off.
- Find every gear you shot. Count them!
- Keep your Gear Shooter in one piece. You need it next time!
- Put spare parts back in the box.
Well done! You were safe and you had fun!
Teacher note
Timing (90 min): photo and talk 5, real world 5, safety rules 5, build 35, break 5, parts 5, ports 5, connect 5, first shot 10, challenges 10, tidy 5.
Safety is the lesson today. The gear leaves the wheel hard enough to sting. Set up a shooting lane on each table (towards a wall or a box, away from the room), and load the gear yourself for the first shot of each child so you can show where it goes. Do not let children lean over the model to look at the wheel while it spins. The Level 1 page has the same warning.
One Large Motor on port A (step 5 of the manual). The Level 1 program spins it clockwise; if a child’s gear goes the wrong way, check the gear train against the manual before changing the direction on the block.
The flywheel needs time to speed up. If 2 seconds only drops the gear, use 3. Very short runs (under 1 second) will not throw.
Words met today: gear, teeth, shooting wheel.
